The purpose of this project is to design and mass-produce kits for a floating tiny house that can sail. It combines high-tech modeling and fabrication and low-tech assembly that can be carried out DIY-style on a riverbank or a beach. This boat is a four-bedroom with a kitchen, a bathroom/sauna, a dining room and a living room. The deck is big enough to throw dance parties. It can be used as a river boat, a canal boat or even a beach house. It's rugged and stable enough to take out on the ocean. Kits will start at around $50k (USD). The design has been tested in simulation and prototype; full-scale production will begin next year.
Tuesday, December 6, 2016
The Final Sheeting Arrangement
Previously, I proposed a design for an automatic traveler system that would move sheet blocks back and forth to counteract the twist. I don’t know whether it would work, because I haven’t tested it, mainly because I don’t like it. It’s too complicated. But I didn’t know what else to do… until yesterday.
Yesterday I looked at some traditional Chinese Junk set-ups, which use twin sheets. There are two separate sheeting set-ups for port and starboard tacks. Having two sets of sheets solves a couple of problems. One is that there doesn’t have to be a gap between the leach of one sail and the luff of the next for the sheets to move through, and a sail can overhang the transom without requiring a boomkin for sheeting, because each sheet hangs to the side of the sail. The other is that with the Junk rig the force on the sail acts differently depending on the tack: on one tack, it pushes the battens against the mast; on the other, it pulls them away from the mast. Because of this, the optimal sheeting angles are different for each tack, but with a single sheet there is just one attachment point on deck.
Now, that alone isn’t too interesting, but it becomes very interesting when combined with QUIDNON’s super-wide deck arches. You see, the twist happens because the forces on the different sail panels are different but the sheetlets all go to blocks that are all the same spot, at the same angle to the sail. But the deck arches allow the sheet blocks to be spaced apart so as to counteract the twist.
I like this solution because of its simplicity. The trade-off is that the running rigging has gained two more lines, because now there are four sheets to manage instead of two. But then that’s not a big increase in percentage terms. Before splitting up the sheets into port and starboard there was the one sheet, two halyards (peak and throat), two topping lifts (fore and aft) and one downhaul. That’s 7 lines per sail. And now there are 8.
The twin sheets have a few additional advantages. They make it possible to backwind the sails, to slow down or even to sail backwards. This is sometimes useful; for example, for sailing into a slip at a marina. (Yes, Junk rigs make it possible to do things under sail that sloop and ketch sailors can only dream of.) It also makes it possible to heave-to in the traditional manner, by sheeting in the main, backwinding the foresail and lashing the tiller to leeward, rather than in the Junk manner—by simply letting go the sheets and playing with the rudder until the sails trail off to leeward at some comfortable angle. When becalmed in a swell they make it possible to tighten both port and starboard sheets so that the sails do not swing back and forth on the swell, snubbing at the sheets. Lastly, if a sheet parts (as they all do eventually) then it is still possible to sail—perfectly well on one tack, less well on the other.
There is just one question left to answer: Does this actually work? (I know, details, details...) Well, I rigged it up on the 1:12 model, and, lo and behold, it does! Here's the money shot: the mainsail sheeted in sets perfectly flat. This is about as good as it gets. This boat is going to sail to windward and short-tack like a dream!
Update 2016-12-16: In discussing this sheeting arrangement with Dave Zeiger (who generally approved of it) it turned out that there is one more problem to solve: when the sail is reefed, more force from the sheet gets concentrated on the boom and the battens that stack up at the bottom of the sail, causing a lot of twist. My proposed solution (to be tested) is to add a row of cam cleats to the front side of the deck arches. The drill is, prior to reefing, walk up to each deck arch, take the appropriate part of the sheet and jam it into a cam cleat, so that the rest of the sheet remains slack and imparts no force on the boom or the other battens stacked at the bottom.